Milsurp stock crack4/9/2023 In a weekend you can get the Uberti to look like a million dollars. I have a wood dowel to hold the forearm and a wood dowel to hold the stock and have them in a 2x4 so the pieces stand up to dry. After every couple of coats (when dry) go over it with 0000 steel wool. Don't apply this finish in anything but thin coats. I use a piece of the old cotton tee shirt folded into a 2 inch square and make long runs following the grain to apply the finish. the first few coats take the longest to dry but after that you can put 2 or 3 coats on in one day. To apply the Tung oil follow the labels directions. When dry use the 0000 steel wool lightly and wipe down with a clean cloth. When it looks nice let it dry 24 hours, I know this part will kill you but it is important. After a few minutes wipe the excess off and see if that is the color you want. Use the Stain with the foam brush applying it heavy and letting it sit. The stock should now be ready for final finishing. Use the 400 grit paper very lightly to knock them off followed by a good rub down with 0000 steel wool. Now hold it about two feet over the stove burner constantly moving it until dry. Once you are happy with your work take it to the kitchen and quickly run the stock under water and pat it quickly to get the excess water off it. The water in the cotton is forced into the wood grain and raises the dent out of the wood. Put the steam iron over it and you will see what happens. Fold it over a couple of time and place it over the dent. With the flat iron set hot enough to produce steam (no hotter) take a 6 inch piece of the old tee shirt and soak it in water and squeeze it out. If there are dents (most likely) then move onto the next step. If there are actual gouges where the wood grain is cut you will have to decide if sanding them out is an option. If the stocks are checkered the old toothbrush works well taking the finish out of the checkering. Once the wood is bare and clean you can apply one more coat of the citristrip, let it sit a few minutes and then wipe it off following with a good rub down with the 0000 (Extra fine steel wool). As you go follow the same routine with the paint stick and steel wool. You will go through a few pieces of newspaper before your done. Change the newspaper and lay the wood down again and do another area. The 00 Steel wool is excellent for taking the finish off after scraping. it won't all come off the first time and will need to be repeated. This wood now will be mostly free of the finish where you applied the citristrip ( It smells nice so you wife won't kill you ) Use the paint stick wearing the rubber gloves and scrape the finish off. This stuff stays active for 24 hours so you could even put it on and leave it for a long time. Now forget about it for about 40 minutes minimum. Apply the Citristrip with the bristle brush liberally ( as thick as you can ) to both pieces covering the sides as much as you can. Lay out a piece of newspaper and lay the forearm and butt stock down. The rifle should be disassembled and the wood placed aside on a good work bench free of debris and clutter. You may be able to remove the fore end without removing the block at the end of the barrel by just sliding the mag tube forward enough to drop off the fore end. Slide the mag tube forward and out, then the block out of the dovetail. Then tap out the pin in the mag tube mounting block on the end of the barrel (this locks the mag tube in place). On a 73 - To remove the fore-stock, you first have to remove the two screws that hold the fore end cap on, and then remove the block that the screws mount to from it's dovetail. Available at most larger Hardware stores.ģ.) Minwax Oil Base stain in your choice of color.ĥ.) Formby's Tung Oil, either high or low gloss. List of items needed.ġ.) Quart of Orange Citristrip gel. Here is the method I use all the time for great results. Over the past several years I have done quite a few Uberti rifles and handgun grips to get the red sprayed finish off. I have been refinishing gunstocks for 30 years on and off. I also do refinish for people who would rather not tackle the job themselves. INSTRUCTIONS FOR REFINISHING A UBERTI STOCK. Longshot Logan's Instructions for refinishing
0 Comments
Leave a Reply.AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |